3com SuperStack 3 T Pdf User Manuals. View online or download 3com SuperStack 3 T Getting Started Manual, Datasheet. User manual for the device 3Com SUPERSTACK T. Online user manual database. Get 3Com SUPERSTACK T Switch User Manual. Get all 3Com manuals!.
|Published (Last):||3 September 2006|
|PDF File Size:||10.23 Mb|
|ePub File Size:||9.57 Mb|
|Price:||Free* [*Free Regsitration Required]|
Environmental Statement It is a 3Com policy to be environmentally friendly in all operations. This manual is printed on paper that comes from sustainable, managed European forests.
The production process for making the pulp has a reduced AOX level adsorbable organic halogen resulting in elemental chlorine-free paper. SuperStack 3 Switch Implementation Guide This guide contains information on the features 4226g by your Switch and how they can be used to optimize your network. CD-ROM to a suitable directory.
Documentation accompanying 3Com Network Supervisor. Table 3 Hardware features The Switch is not manuao power or there is a fault with the Power Supply Unit.
Redundant Power To protect against internal power supply failure, you can use this socket Water or moisture cannot enter the case of the Switch. Air-flow is not restricted around the Switch or through the vents in the side of the Switch.
Air temperature around the Switch does not exceed 40 The air is as free from dust as possible. To rack-mount your Switch: The unit LEDs will display the unit number in the stack, from 1 at the bottom to 4 at the top. Use the following sequence of steps to power-up the Switch. Switch Family 1 Plug the power cord into the power socket at the rear of the Switch. If a Unit LED is off, initialization is not complete. MDI port, you need to use a standard straight-through manuap.
See 3Com recommends that you use Category 5 twisted pair cable — the maximum segment length for this type of cable is m ft. If you want to install the Switch using a Category 5E or Category 6 cable, 3Com recommends that you briefly connect the cable to a grounded port before connecting network equipment. Use the following sequence of steps to activate the GBIC ports.
SC connector on the transceiver. However, to make full use of the features offered by the Switch, and to change and monitor the way it works, you have to access the management software that resides on the Switch.
The whole setup process is summarised in mnual contained in the sections that follow. Static IP addresses are necessary to ensure that the Switch is always allocated the same IP information.
For most installations, 3Com recommends that you configure the Switch Kanual information manually. You must do this whilst the Switch is offline, that is, before you connect the Switch to a network. You can do this using the Web interface or the command line interface CLI via telnet.
Using the Web Interface 1 Power-up the Switch. The final page displays a summary of the information entered. The initial set up of your Switch is now complete and the Switch is ready for you to set up your chosen management method.
The screen displays a summary maunal the information entered. This software allows you to communicate with the Switch via the console port directly, or through a modem. Documentation supplied with the terminal emulation software.
You are now ready to view the automatically allocated IP information using the command line interface. As soon as a network connection is made the Switch begins the automatic IP configuration process. A summary of the automatically allocated IP information is displayed.
Make a note of the Network IP Address. For example, you can use the 3Com Network Supervisor Switch page To manage a Switch using the command line interface over a network the Network using Telnet: If the login prompt does not display immediately, press Return a few mwnual until it starts.
Passwords command line interface, or to change the 4226r passwords, you need to log in with a valid user name and password. The Switch has three default user names, and each user name has a different password and level of access.
There is 4226r an explanation of IP addressing. The topics covered are: The ,anual has identified that the GBIC does not meet the minimum requirements for the Switch and has disabled the port. If your IP network is internal to your organization only, that is, you do not access the Internet, you may use any arbitrary IP address as long as it is not ,anual used by another device on your network.
X where X is a number between 1 and with a subnet mask of You must 4226tt the following safety information before carrying out any installation or removal of components, or any maintenance procedures on the Switch Series. Warnings contain directions that you must follow for your personal safety.
Follow all directions carefully. Installation and removal of the unit must mwnual carried out by qualified personnel only. If installing the Switch Series unit in a stack with SuperStack II or SuperStack 3 units that are narrower than the Series, the Switch Series unit must be installed below the narrower units.
If connecting a modem to the console port of the Switch Series, only use a modem which is suitable for connection to the telecommunications system. These are shielded RJ data sockets. They cannot be used as standard traditional telephone sockets, or to connect the unit to a traditional PBX or public telephone network.
Download free pdf for 3Com SuperStack 3 T Switch manual
More information on 3Com maintenance and Professional Services is available at http: This query-based interactive tool is located at http: To send a product directly to 3Com for repair, you must first obtain a return authorization number RMA. These limits are designed to provide reasonable maual against harmful interference manua the equipment is operated in a commercial environment. Page of 84 Go. Table of Contents Add to my manuals Add. Switch 3Com G Configuration Manual 3com switch g family pages.
3Com 4226T Switch User Manual
Page 2 Environmental Statement It is a 3Com policy to be environmentally friendly in all operations. Related Documentation SuperStack 3 Switch Implementation Guide This guide contains information on the features supported by your Switch and how they can be used to optimize your network.
About The Switch Family Family consists of: Package Contents Water or moisture cannot enter the case of the Switch. Rack-mounting To rack-mount your Switch: The Power-up Sequence Use the following sequence of steps to power-up the Switch.
Page 29 SC connector on the transceiver. Page 37 The final page displays a summary of the information entered. Page 43 1 Connect the workstation to the console port using a standard null modem cable as shown in Figure 13 Connecting a workstation to the Switch via the console port To connect the cable: Page 44 You are now ready to view the automatically allocated IP information using the command line interface.
Setting Up Web Interface Management If the login prompt does not display immediately, press Return a few times until it starts. Pre-requisites Passwords command line interface, or to change the default passwords, you need to log in with a valid user name and password.
Solving Stack Formation Problems If your IP network is internal to your organization only, that is, you do not access the Internet, you may use any arbitrary IP address as long as it is not being used by another device on your network.
A Safety Information You must read the following safety information before carrying out any installation or removal of components, or any maintenance procedures on the Switch Series. This manual also for: Superstack g Superstack t 3ca Superstack 3 t Superstack 3 t Superstack 3 g Show all Superstack 3 3c Superstack 3 3c Superstack 3 3c Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page.
To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?