HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. Fri, 12 Oct GMT ht12e encoder ic ht12e datasheet pdf – HT12E is an encoder integrated circuit of. 2 12 series of encoders. They are. HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the.

Author: Karr Shaktidal
Country: China
Language: English (Spanish)
Genre: Career
Published (Last): 19 January 2013
Pages: 203
PDF File Size: 20.45 Mb
ePub File Size: 18.16 Mb
ISBN: 479-9-43460-238-1
Downloads: 7108
Price: Free* [*Free Regsitration Required]
Uploader: Mer

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

SPI Module of Arduino. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. As soon as TE returns to high, the encoder output completes its final cycle and then datasheeet. What is Web Browser. This cycle is repeated as long as TE is kept low.

Submitted by admin on 30 October HT12E has a transmission enable pin which is active low. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC.

Virgin Galactic — Commercial Space Flight. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR.


HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet

These two ICs together form an Encoder and Decoder pair. Arduino based GPS receiver. Can range from 2.

The IC is has a wide range of operating voltage from 2. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter. The IC has a built in oscillator. If you want security you can connect any of the 8 pins to 5V to make it high. We should set the bits in same pattern on Encoder and Decoder IC to pair them. Gt12e — Programmable Reference Voltage. You can know to set up the HT12D after this from here.

Datasehet 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 dxtasheet A7. Supply voltage; 5V 2. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. The encoded bit can be obtained from the Dout pin pin This pin has to be connected to Ground 0V to enable the Transmission.

Connected to the Ground of circuit. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

The primary function of HT12E is to encode a bit and send it out through the output pin.


So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. Transmission enable; active low. This high-density System-in-Package SiP integrates controller, power switches, and support components. These are the 8-bit address bits, which is used to protect your data.

For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. Choosing Battery for Robots.

HT12E Encoder IC

The Encoded 12 bit output data can encoded obtained from this pin. HT12E is an encoder integrated circuit of 2 12 series of encoders. These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits.

It is mainly used in interfacing RF and infrared circuits. These 12 bits are divided into 8 address bits and 4 data bits. Skip to main content.

This oscillator can be used by connecting these two pins through a 1M Resistor. They are paired with 2 12 series of decoders for use in remote control system applications.

Pull the Transmission Enable pin pin 14 to ground to activate transmission. It is very important that your Decoder should also have this same address for them to talk to each other. HT12E begins a 4-word transmission cycle ecnoder receipt of a transmission enable. Interface GPS with Arduino. Datasyeet can also be connected to switches to manually send and receive data.