Seamless Fittings per ASTM/ASME A / SA in a variety of stainless grades: /L; H; ; /L; ; /H; /H; Duplex ASTM A Standard Grades are designated with a prefix, WP or CR, based on the applicable ASME or MSS dimensional and rating standards, respectively. ASTM A / ASME SA ASTM A / ASME SA ASTM A / ASME SA ASTM A TUBE ASTM A / ASME SA ASTM A / ASME SA
|Published (Last):||2 February 2016|
|PDF File Size:||4.33 Mb|
|ePub File Size:||14.45 Mb|
|Price:||Free* [*Free Regsitration Required]|
Stainless Steel Fittings Manufacturers in India. Specific requirements are covered elsewhere. Class designations are also utilized to indicate the nondestructive test method and extent of nondestructive examination NDE. A combination of values from the two systems may result in nonconformance with the specification. All sales are governed by our terms and conditions, which are available on request.
Wrought stainless steel butt-welding fittings. Socket Welding and Threaded Forged Fittings.
There are no classes for the CR grades. Fittings supplied under this specification shall be examined visually for surface discontinuities, surface checks, and mechanical marks. The contents of this website are presented for information purposes only, and while effort has been made to ensure their as,e, they are not to be contrived as warranties or guarantees, expressed or implied, regarding the products or services described herein or their use or applicability.
Within the text, the SI units are shown in brackets. The material for fittings shall consist of stainless steel forgings, stainless steel bars, stainless steel plates, or seamless or welded stainless steel tubular products. All fittings shall undergo heat-treatment. ASTM does not give any warranty express or implied or make any representation asje the contents of this abstract are accurate, complete or up to date. We reserve the right to modify or improve the designs or specifications of our products at any time without notice.
Elbows are produced according to the following standards: There are no classes for the CR grades. DIName grade St. Link to Active This link will always route to the current Active version of the standard.
ISO Approved Manufacturer & Exporter of ASTM A403 WP 304L Stainless Steel Buttweld Pipe Fittings.
Class designations are also used to indicate the nondestructive test method and extent of nondestructive examination Adme. Chemical and product analyses shall be performed and shall conform to the required chemical composition in carbon, manganese, phosphorus, sulfur, silicon, chromium, molybdenum, and titanium. Historical Version s – view previous versions of standard.
This specification covers the standard for wrought austenitic stainless steel fittings for pressure piping applications.
S ENsteel gades: Chemical and product analyses shall be performed and shall conform to the required chemical composition in carbon, manganese, phosphorus, sulfur, silicon, chromium, molybdenum, and titanium.
It is easily accessible through NH No. Fabricated large size stainless steel fittings, duplex stainless steel buttweld fittings, stainless steel elbow, stainless steel tee, stainless steel reducers, stainless steel cap, stainless steel stub ends. Steel reducers are produced according to the following standard: A table gives the general summary of the fitting classes applicable to all WP grades of stainless steel covered by this specification.
Stainless Steel forging or shaping operations shall be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending, fusion welding, machining, or by a combination of ssme or more of these operations.
DINsteel grades: Forged steel fittings socket-welding and threaded. Combining values from the two systems may result in non-conformance with the standard.
We have invested 3 million dollars 20 Million Rupees to upgrade our factory making it of world level with high grade sophisticated production equipments producing all grades of Pipe FittingsButt Welded FittingsFlanges with atomization and electric q403 control with green technology.
Forged or rolled alloy steel pipe flanges, forged fittings and valves and parts for high temperature service. This abstract is a brief summary of the referenced standard. Always verify that you have the most recent product specifications or other documentation prior to the installation of these products.
It is informational only and not an official part of the standard; asje full text of the standard itself must be referred to for its use and application. If exact equivalents are needed original specifications must be consulted. The material for fittings shall consist of forgings, bars, plates, or seamless or welded tubular products.
Forging or shaping operations shall be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending, fusion welding, machining, or by a combination of two or more of these operations. Stainless Steel Pipe Fittings Manufacturers. Table 1 is a general summary of the fitting classes applicable to all WP grades of stainless steel covered by this specification.
They are produced according to the following standards: DINsteel grades St. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. Now FitTech has emerged with high volume of quality production at reduced time with competitive price focusing totally on customer satisfaction with high class quality with committed early delivery at competitive price.
Standard Specification for A / SA
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. A L Stainless Steel covers the standard for wrought austenitic stainless steel fittings for pressure piping applications.
Work Item s – proposed revisions of this standard. These comparisons are approximate only. Specific requirements are covered under another specification. Tension test shall be done on the fitting material to determine the tensile properties such as yield strength and tensile strength.